Most often, self-leveling flooring on wooden floors is found in homes wooden type. Perhaps these are village houses built a long time ago or large cottages, built according to modern projects from a log house. In any such house it is possible to install a self-leveling floor. Perhaps someone will make a small discovery for themselves, but making a self-leveling floor in a wooden house today is not considered a particular problem. Modern polyurethane mixtures allow you to create any coating. The only and important condition is the complete readiness of the wooden floor.

Modern elastic, fast-acting self-leveling flooring is considered an excellent replacement for expensive particle boards. Together with a special reinforcing mesh, a special universal primer, a system is created that helps overcome the stress experienced by a wooden floor that does not have cracks. The result is an absolutely smooth coating on which a variety of operations can be carried out. You can put carpet, stick ceramic tiles or just paint it. A wooden floor must have a layer of self-leveling flooring with a maximum thickness of 20 mm. After 5 hours have passed after applying the coating, walking on the new floor is allowed. wooden floor after 12 hours, it becomes possible to carry out further work.

And, of course, in order for the installation to proceed efficiently, prepare in advance:

• empty containers;
• screwdriver;
• perforator;
• hammer;
• rule;
• level;
• roulette.

What kind of floors do wooden houses have?

Wooden houses, similar to residential premises, require special attention to the arrangement of the floor, since the rooms in such a house are usually located on ground floor. That is why the coating must be absolutely smooth, look attractive and must be insulated.

In most cases, a wooden house has two types of floors. They can be concrete, or they use wood. Moreover, the concrete floor has the most advantages. This type of floor requires a small investment, there is much less fuss with it, and it does not require special professional skills to install such a coating. However concrete covering- this is the weight that puts increased pressure on the foundation of the building. Any vibrations of the walls can cause cracking of the base, as a result of which the thermal insulation ability of the material will be lost.

A wooden floor is more resistant to any vibrations of the walls, it meets all environmental requirements. Such a wooden floor can be easily processed, rotted boards can be replaced, and all work can be carried out even after the complete installation of the wooden floor. The negative side of such a floor is its high cost; the work of installing a wooden floor can only be performed by professional workers; it is almost impossible to obtain an absolutely smooth surface.

Preparing the base for pouring mortar

How high the quality of the coating will be depends largely on the most important stage, during which the foundation is prepared. Failure to follow the step-by-step, competent technology for producing self-leveling floors will lead to cracking of the coating, it may begin to deteriorate, peeling will be observed, occurring before its service life. Only solid foundation made with high quality can become a quality guarantee of long-term operation flooring.

Sometimes a self-leveling floor is installed directly on an antique wooden floor. In this regard, the wood must be sanded using sandpaper to obtain a rough structure. Treated boards must be painted with a special primer. If the first layer is not very strong and monolithic, it is necessary to apply several more layers. The surface of the wood should be free of grease, varnish and oil stains.

The next step is to remove installed skirting boards fill any cracks in the floor with blocks. Wooden floors need to be cleaned very thoroughly using a scraper. When performing such an operation, you need to pay a lot of attention to the existing inter-board joints and expose all existing cracks. Using a vacuum cleaner, it is necessary to thoroughly clean the surface of the self-leveling floor and degrease it using cleaning powder.

After this, the well-treated cracks must be sealed using mortar and the surface leveled. Then lines are drawn along the entire perimeter of the room, the length of which is less than the length of the room. Screws are placed along each line, maintaining a step of 30 cm. With the help laser level the highest point on the surface of the self-leveling floor is found.

The screws must be screwed in at the same level.

Moreover, they need to be screwed into the ends at an angle of 90 degrees along previously drawn lines. Place several pieces of alabaster near each screw.

The next step will be laying the beacons that are required for the self-leveling floor. They are installed directly on the screws. There should be no subsidence of the beacons; if this happens, they need to be cemented.

Some features

Before you begin installing a self-leveling floor on a wooden floor, it is necessary to lay mounting tape. This will be a damper gasket; it will protect the surface in case of expansion as the temperature increases.

After completing all the preparatory work, you need to determine the air humidity and temperature in the room. Production technology very often requires that these parameters have certain values. This is especially true for self-leveling floors where wood is used.

The prepared solution is immediately poured onto an area equal to 2 square meters. m. The solution is leveled using beacons. To obtain uniformity, it is rolled with a needle roller. When carrying out work, it is necessary to ensure that the lift of the self-leveling floor is maintained in relation to installed beacons. The poured floor must dry thoroughly.

After the surface has set and completely dried, a finishing coating consisting of varnish and resin is poured. It will give the finished coating a magnificent glossy shine and improve its strength characteristics.

Self-leveling floors have recently become increasingly popular. This is due to the fact that thanks to them it is possible to obtain an almost ideal surface that is resistant to mechanical stress and can easily withstand a humid environment.

Moreover, the components of such mixtures can make it possible to install a self-leveling floor on a wooden floor, without first creating a screed.

Installation

First of all, it should be noted that the wooden surface should not be rotten or loose. There should be no significant damage or large irregularities on it. Otherwise, self-leveling floors should not be applied to wooden floors.

Preparatory work

• First you need to dismantle the old ones. At the same time, their fastening elements are also removed.
• At the next stage, it is necessary to scrape the floor, removing a small layer of material. This is done not only in order to detect all the cracks, but also taking into account that a self-leveling floor on a wooden base will raise its level, which means it is necessary to remove a little of the surface.
• Next, the floor is carefully inspected to detect cracks, which are marked with a marker. This defect can also include gaps between boards.

• Then, using putty, all damage is repaired. It is worth noting that the installation instructions recommend using material designed for working with wood.
• After this, the surface is covered with a layer of primer with an antibacterial coating. It should not only increase adhesion, but also provide protection for the wood.

• In order for the self-leveling floor for wooden bases to obtain a good connection with the surface, it is necessary to apply a second layer after 4 hours. In this case, you can add a small amount of sifted corundum to the mixture.

Advice!
Some craftsmen first recommend applying a layer of primer intended for working with wood, and then a material for concrete work.
However, this is not necessary when incorrect selection components may cause an unnecessary reaction.

Fill

• Before applying self-leveling flooring on a wooden floor, you need to install a special tape around the perimeter of the walls. It will act as a damper pad, protecting the surface from the effects of expansion when heated.
• It is also necessary to install special benchmark beacons. This is necessary so that self-leveling wood floors have a certain level, which they control.

• It is worth noting that the beacons are placed according to the water level, and the distance from the floor is set in accordance with the required layer of the future screed. It is worth remembering that for this type of work it is better to use thin-layer mixtures that allow you to obtain a coating with a thickness of 1 to 5 mm. This is due to the fact that the coating is applied to the finished floor, which means there is no need to create differences at the threshold.
• After everything preparatory work produced, it is necessary to check the room humidity and air temperature. Compliance with certain values ​​of these parameters is often required by production technology, and given the fact that self-leveling floors are installed in wooden house, then this requirement should be approached especially carefully.

• The floor is poured in one stage, starting from the deepest places.. In this case, you can use a special soft spatula, which distributes the material over the surface. You can make it yourself by attaching a soft but wide tool to a long wooden handle.
• During installation, quite often there is a need to move along a surface that has already been poured.. For this purpose, special linings for the soles of shoes with spikes have been developed.

• To ensure that the self-leveling floor in a wooden house does not contain small air bubbles, you should walk over it with a plastic roller with long spikes. It is specially designed for the installation of such floors and, especially for mixtures with rapid hardening.
• When self-leveling floors are on wooden base applied, all beacons should be removed from the surface. After this, you need to wait until it hardens completely.

• It is worth noting that the period after which you can walk on the surface is indicated on the packaging of the mixture.. At the same time, professionals recommend not starting other work on the floor earlier than in a week.

Advice!
To remove moisture from the room and maintain the required temperature in it, you can use a household air heater with a fan.
This way the process will happen much faster.

Conclusion

It is worth noting that there are special brands mixtures for self-leveling surfaces, which were developed for application to wood. They have high level adhesion to this material and have great plasticity, retaining all the necessary properties. However, not all manufacturers produce them, citing the fact that they have universal components for such work." width="640" height="360" frameborder="0" allowfullscreen="allowfullscreen">

Conclusion

In the presented video you will find additional information on this topic. Also, based on the above text, we can conclude that the price of work on creating self-leveling floors is wooden surface will be somewhat less than when organizing preliminary screeding or leveling large differences. Therefore, if the coating is in satisfactory condition, then pouring is done directly over it.

It is worth noting that there are special brands of mixtures for self-leveling surfaces that were developed for application to wood. They have a high level of adhesion to this material and have great ductility, retaining all the necessary properties. However, not all manufacturers produce them, citing the fact that they have universal components for such work.

Quite often, during renovations recently, self-leveling floor systems are used, which are characterized by durability, wear resistance and strength. Among their positive qualities are safety and environmental friendliness. Since the creation of such coatings, significant technical changes have occurred. For example, they are presented in a wide range color scheme, which is especially true. With their help, you can create real masterpieces of design.

Can wood be used as a base?

Quite often, craftsmen ask the question of whether it is possible to install a self-leveling floor on a wooden floor. The answer is yes, but before laying such a coating, it is necessary to analyze the rough base and determine whether it requires preparation. Realize installation work on wood is necessary only if it is well preserved, and it is recommended to use a thin mixture for arranging the finishing surface, which will not be able to increase the height significantly.

Preparatory work

The self-leveling can be installed not only on the type of rough foundation described above, but also on concrete. Before pouring, any surface must be prepared; the first step is to remove the baseboards and remove the fasteners from the walls. Then the master scrapes the surface; for this you should use the appropriate equipment. If the room has a small area, then it will be possible to cope with the help of a manual cycle. The next step is to hide the cracks using encryption machine. Such errors during operation in any case appear on wooden covering. The resulting irregularities and crevices are treated with putty, which after application is left to dry completely. Then the surface should be sanded with coarse sandpaper, which will improve the quality of adhesion.

The self-leveling floor on a wooden floor will last a long time if the base is cleaned of dust after sanding. It is most effective to use for this. Before priming, the base is degreased. The primer is necessary to increase the adhesion strength of the material to the wood. The composition is applied in two layers; before carrying out work, sifted quartz sand can be added to it. This will ensure the most reliable adhesion between the polymer coating and the base.

Preparing tools

If you are wondering whether self-leveling floors can be applied to a wooden floor, then the answer will be clear. Such work is carried out quite often today. It is important to properly prepare the surface and ensure that you have the appropriate tools. To dismantle the skirting boards you will need wooden wedges, a nail puller and a chisel, but to process wood you need to prepare a sanding machine and a grinding device. You can finally prepare the surface using coarse sandpaper; an industrial vacuum cleaner will allow you to clean the base. To apply the primer to the surface you will need a brush or roller. Quite often these tools are used in tandem, since not all hard-to-reach places can be treated with a roller. A short-haired roller and a flat brush will allow you to distribute most effectively. The craftsman will need a spatula and a squeegee. It will be possible to mix the solution for arranging a self-leveling floor construction mixer or a drill. Self-leveling floor wooden base It is best to pour in special clothing, wearing safety glasses, a respirator and gloves. To move on the surface you will need special soles with spikes. This will allow the master to move around the freshly laid layer.

Work technology

Laying a polymer floor on a wooden floor is no different from the procedure that involves using concrete as a base. The only difference is preparatory stage, which was discussed in more detail above. Before pouring the self-leveling floor, you should prepare the solution using the instructions. The dry mixture should be mixed with water until a homogeneous mass is formed. The resulting solution is laid out on the base, and it is necessary to advance from the far corner of the room.

The self-leveling floor is poured onto a wooden floor, then leveled using a spatula until it is possible to achieve required thickness layer. If we are talking about a wooden covering, then the thickness should be five millimeters or more. As the most optimal and convenient tool a needle roller acts to level and combat bubbles. The intervals between pouring batches should not be more than 10 minutes, otherwise the joints will be clearly visible. But even in this case, the connection of the mortar strips must be carefully rolled with a roller. As soon as the pouring is completed, you should cover the curing surface with film; this must be done 15 minutes after completion of the work. This will prevent dust from settling. After applying the base layer and its hardening, you can begin to apply the finishing coating, which can be a varnish or a polymer.

Cost of work from specialists

The self-leveling floor on a wooden floor will hold quite firmly if you follow the instructions provided. This process can be called quite simple, and you can do it yourself. But if financial capabilities allow, it is recommended to hire a team of specialists who guarantee high quality executions, carry out installation according to technology, and also provide a guarantee for the work done. As a rule, specialists use expensive construction tools. All this adds up to the cost of preparatory, priming work and manipulations for pouring the mixture. In one square meter to prepare a wooden base you will have to pay 400 rubles, while applying a primer costs 200 rubles. per one square meter. Specialists fill the surface with quick-drying liquid compounds for 400 rubles. per one square meter.

If you want to make renovations in a residential area, it is recommended to choose mixtures based on polymer resins. If there are areas of high humidity, then epoxy filler should be used in them, while polyurethane flooring is suitable for other areas of the house. If you are wondering whether it is possible to pour a self-leveling floor, a wooden floor can be an excellent base. If there is a plank covering, it should be repaired and the peeling floorboards replaced. The fasteners are tightened, the cracks are filled with sealant or the latter is mixed with an equal volume of sawdust. Waterproofing should be laid on the wooden base. Do not neglect the need to apply a primer, two layers of which will facilitate the main work and increase the strength of the coating.

Secrets of using finishing mixtures

A self-leveling floor on a wooden floor will look very good if the rough base does not have rough relief flaws. It is advisable to exclude them, since the thickness of the laid layer does not exceed 5 millimeters. Even though the bumps and depressions can be smoothed out by a leveling compound, there is a strong argument for eliminating the defects. Self-leveling floors will harden unevenly, and the strength indicator will vary.

It is also important to choose the right dry composition, the ingredients of which will determine the purpose of the future floor. For example, if the mixture contains cement as a binder, then this composition is suitable for pouring floors in bathrooms, kitchens, showers and bathrooms. If we're talking about about mixtures with gypsum in the composition, then such a floor is best used for rooms with dry and low humidity levels, where it will demonstrate all its positive qualities self-leveling floor A wooden surface can also be used for a base in which a heating system will be present. In this case, you should choose a leveling mass that has increased elasticity. It will expand and contract during operation without cracking.

Conclusion

Sometimes the self-leveling floor is separated from the wooden surface with oiled paper, which is covered with an overlap. In this case, the layer should be poured one or two centimeters thick. The boundary between the screed and the self-leveling floor should be formed by treating the surface with waterproofing impregnation.

A house starts from the foundation and your apartment, room or any technical space starts from the floor. This is the surface that is subject to the greatest spring impact - walking, running, furniture pressure, dust settling, stains. Of course, this indicates the need to form a durable, durable coating. Like many modern construction works, the floor can be made using the latest developments. There are two types of base - concrete and wood. The first is suitable for factories, enterprises, offices, homes, public institutions such as schools, hospitals.

Wooden floors can now be found in the private sector - in cottages, houses in eco-villages, as well as in areas of old buildings. But, nevertheless, this particular material has unique natural properties and very valuable. For rooms with an imperfectly prepared rough surface, self-leveling mixtures for wooden floors are recommended. They will help you find a compromise between time-tested materials, economic considerations and dreams of a fashionable and stylish interior.

Preparing the surface for work

The floor is not always level. Often the surface retains the flaws of the past repair teams, sometimes it becomes deformed over time. In order to determine the condition of the underlying wooden floor, some work needs to be done. First of all, you need to get to it by removing layers of the finishing coating, which can be linoleum, carpet, laminate. This must be done carefully, without deforming the base. To do this, you should first take a closer look at the type of fastening in order to purposefully direct the force. When the surface is cleaned of both the coating and the layer of insulating film and insulation, you need to pay attention to the boards. If you notice signs of rotting, they are no longer suitable, as this process is irreversible. The appearance of small “bugs” is also an alarming symptom. If the tree is not damaged, you can take steps to restore it and lay a new coating.

Evenness is very important when arranging a floor. It will avoid problems with laying ceramic and cork tiles, laminate layers, solid wood boards or veneered MDF. Any excess bend will inevitably affect the appearance of the surface, forming bumps, cracks, and preventing good adhesion of the glue. How do you know what the quality of your floor is? To do this, you can not only use an eye meter, but also count using several threads stretched over the floor from one wall to another. Fasten the ends of the threads at the same height from the floor, then lower them to the level where the thread touches the floor at one point. Measure the distance from the thread to the floor in other areas. If the difference in height does not exceed a few millimeters, this is an acceptable error. If the height difference is more than 5 mm, additional screed will most likely be required in this area. If there are gaps in the floor, they must be sealed with putty, otherwise the mixture will leak and unevenness will appear.

Composition and features of the mixture

Leveling mixtures can be a real help in the hands of a master, both for cement and wooden floors. They prepare the base for any type of finishing. Some of them need to be carefully rolled out over the surface and distributed manually, while some spread on their own, filling all the cracks and depressions. It is the latter types of mixtures that are easiest for a beginner to work with.

The composition traditionally includes cement or gypsum, sand, as well as additional additives that are responsible for the properties of the product - drying speed, strength, preferred layer thickness. It is very important to follow all manufacturer's instructions. The main difference between the mixture for leveling a wooden floor is the presence of fibrous additives that are responsible for better adhesion to the surface, such as fiberglass. Features also include the absence of casein, a substance that can destroy the structure of wood. The composition may also contain polymer modifications.

Necessary equipment

Self-leveling mixtures are also called self-leveling floors, which clearly describes the method of their application. If your room may be subject to temperature changes and high humidity in the future, it is better to choose cement-based mixtures. Anhydride compounds are not ready for such a load. The purchase must be made in hardware store, they will tell you which samples interact best with wood, and how to calculate the required volume of the mixture. From necessary tools you should have: a bucket, a wide spatula, a needle roller and a mixer for the solution. Proven manufacturers in this area: Knauf, Horizon, Vetonit, Ceresit, Prospectors, Volma, Paul Bolars.

Dilution of the mixture

Leveling a wooden floor with a self-leveling mixture can be a real torture if the ratio of water and dry matter is not observed. The mixture is poured into the water gradually, stirring. It is very important to have time to mix the mixture and apply it without exceeding a time period of half an hour, since it is at this time that the mixture has the best adhesion to the surface. If there is too little water, the mixture will begin to harden and be distributed into granules-crystals while still in the mixer, but if there is more than required, the self-leveling floor will take a long time to dry.

This work is difficult to carry out alone, so it is better to invite specialists or friends who are competent in construction matters. The mixture costs a lot, but just improper mixing can render it unusable, because the frozen mixture can no longer be re-diluted with water and used again. Stir the mixture until the lumps are completely dissolved. It is better to isolate the room from flows fresh air, closing the windows. Drafts and high humidity may adversely affect the hardening of the coating. Best temperature for work – from 5 to 25 degrees Celsius. If the mixture does not spread properly, use a roller. If its needles are shorter than the thickness of the floor, they will break up air bubbles without affecting the distribution of the mixture as a whole.

If you are making a floor in a room where there is no floor that separates it from the adjacent one, install limiters in advance that will keep the adjacent room clean. They can also be installed near the plumbing fixtures if you plan to decorate them artistically.

It is quite possible to do such work with your own hands. Purchasing a high-quality mixture will ensure ease of work, efficiency - a good result.

Application of self-leveling floor

Self-leveling floors have certain advantages. They are environmentally friendly and safe. Their thickness varies from a millimeter to several centimeters, which allows you to find your solution. Their thickness does not take away the height of the room, allowing you to freely manage its space. The result of the work is a perfectly even, smooth, durable coating, which is ready for further work. You can install a floor heating system on it, or you can immediately lay the finishing layer. The floor covering can be anything, since self-leveling flooring does not react with any material. The temperature of the medium and the temperature of the water with which the mixture is diluted are very important; it should be cold, at room temperature.

The work can take the whole day, since both preliminary measures and sometimes a multi-level pouring process are necessary. The leveling compound may leave debris that is unacceptable on a wood floor. Cleaning the area for the finishing coat will take about an hour.

Most mixtures cannot be used as a topcoat and require a topcoat of other materials. Some of them can be topped with paint.

The arrangement of your home must necessarily begin with a room design, and it must include space not only finishing coatings, design solutions in color and accents, but also in basic construction work. You can't build a castle on sand, and you can't get safe and durable housing without such a foundation. Self-leveling compound is worth the cost, good insulation and filling of voids and cracks is very important for a wooden floor. This material breathes, but at the same time it becomes vulnerable, so only mixtures specially designed for wood can help solve the issue of quality repairs.

The 21st century is the time that made self-leveling floors on a wooden base so popular and in demand both in residential premises and in modern offices. Today, self-leveling floors on wooden floors are not just a covering, but also an excellent decorative solution, especially if 3D imaging technology is shared. Such floor coverings have many advantages and are worthy performance characteristics, as well as a completely affordable price. Few people know how to make a self-leveling floor on a wooden floor with their own hands, but it is not as difficult as it might seem at first. This guide will help you make a self-leveling floor on planks.

What types of self-leveling floors are there on a wooden base?

Self-leveling flooring on a wooden base is not just one solution, but a whole category of materials that are applied to concrete or wood (as in in this case) basis. Self-leveling floors on wooden floors can be divided into:

• Polyurethane. A durable polymer floor that is resistant to prolonged exposure, which is ideally suited for arranging flooring in places with a large number of people.
• Epoxy. These are self-leveling floors on a wooden floor that do not react in any way to moisture. It is recommended to install such floors in wet areas, especially in the bathroom and kitchen.
• Epoxy-urethane. A type of polymer floor that has good strength and wear resistance. Can be used as an alternative to polyurethane coating.
• Methyl methacrylate. Polymer floor with excellent thermal insulation properties, is often used for arranging floors in rooms without heating or with poor heating during the cold season.

Do-it-yourself self-leveling flooring on a wooden floor can be one-component or two-component. The first type is often used as a basis for installing parquet, stone, tiles or other decorative covering. Two-component coatings often contain three-dimensional image, which gives the floor a creative and unusual appearance. Next we will figure out whether it is possible to make a 3D floor on a wooden floor and how to do it.

The main advantages of self-leveling floors on a wooden base

A poured floor on a wooden floor is a solution that has gained its popularity not only due to its appearance, but also because of its good technical characteristics and numerous advantages. They can be found below:

• High resistance to prolonged mechanical stress, resistance to wear and abrasion.
• Excellent impact resistance chemicals– wood-look self-leveling floors will withstand even acids.
• Wide range of available color solutions, design styles, patterns and textures, images.
• Excellent sound and heat insulation properties - creative self-leveling wooden floors are quiet and warm!
• High strength, reliability, long service life of the coating, which will last for decades.
• The presence of antistatic properties, thanks to which the self-leveling wooden floor is quite easy to clean.
• Absolute seamlessness - this simplifies the process of maintaining the floors and prevents squeaks from the coating.

You can see that the self-leveling floor in a wooden house is not only modern and beautiful, but also practical solution, which can delight the inhabitants of the home for many years. In addition, such a coating can be equipped on its own. We will learn how to fill a wooden floor with self-leveling flooring, what tools and building materials are needed for this.

What tools are needed to install the floor?

Do-it-yourself self-leveling flooring for wooden bases requires the use of a wide range of tools, devices and materials that must be prepared before starting work. You should definitely have on hand:

• A special mixture for self-leveling flooring is the basis of the future floor covering.
• Long spatula, needle roller (necessary for removing air bubbles).
• A construction mixer or a drill with a special attachment if you don’t have a mixer.
• Laser or ordinary building level, aluminum rule.
• A container of at least 20 liters, a set of construction beacons and wooden blocks.
• Alabaster, mortar, water in sufficient quantity for the mixture.
• Triangular scraper, screwdriver, screws, dowels, long ruler.

It also wouldn't hurt special clothing– protective gloves, eye and face masks, as well as shoes designed for walking on painted surfaces (paint shoes). After preparing the necessary arsenal, you can begin.

Preparing the base for a polymer floor

Is it possible to pour self-leveling floors on a wooden floor? Yes, sometimes craftsmen do not ask themselves whether it is possible to make a self-leveling floor on a wooden floor and apply the solution directly to the old coating. However, even in this case, it is necessary to carefully prepare the base of wood - it should be sanded well so that the surface becomes rough. This will significantly improve the adhesion of the floor to the layers. polymer coating. It is also worth making sure that there are no traces of grease, dirt, oil and other contaminants on the wooden floor surface - they are removed with a solvent.

Is it possible to apply self-leveling flooring to a wooden floor if it creaks? No - otherwise the final coating will lie unevenly and cause a lot of problems. To avoid trouble, you also need to check the floor. All boards must be securely fastened in the correct position, the floor itself must be level, without unevenness or defects. Also, before applying the polymer floor, you will need to remove all paint from the surface of the base, if there is any.

Before making self-leveling floors in a wooden house, you need to do a little preparation of the coating:

• Remove all baseboards and close the holes created by removing the baseboards.
• Seal all cracks, chips and uneven areas on the floor surface with mortar.

Now you can begin actions that will ultimately lead you to completing the installation of the self-leveling floor.

Level the surface and install beacons for the floor

In order for the floor to be as level as possible, you need to take care of it initial stages. So, before pouring the solution, draw a line along the entire length of the room, then place self-tapping screws along it, the distance between which is 30 centimeters. Using laser building level you will need to find the highest point located on the wooden base for the polymer floor. After detection, you need to add about 5-6 mm (the thickness of the floor layer) and align the screws at the same level. It's still too early to do 3D flooring on wood floors.

The next stage, which continues the installation of a self-leveling floor on a wooden floor, is the placement of beacons. They must be placed on previously installed screws, securely fastened using mortar. After this, you should prepare a solution for the self-leveling floor - to do this, the contents of the package must be mixed in a container with water according to the instructions indicated on the package, and then stirred until smooth with a construction mixer.

Let's start pouring the mortar for the self-leveling floor onto the wood

We already know whether it is possible to use a self-leveling floor on a wooden base. The solution prepared in advance should be carefully poured onto the prepared base, covering an area of ​​about 2 square meters at a time. meters. The layer must be leveled along the beacons using a long spatula. When the formation of the layer is completed, you will need to remove all air bubbles on the surface of the coating using a needle roller - this is very important stage, on which it depends further fate the whole result. Wait until the floor is completely dry.

Now you know how to make a self-leveling floor on a wooden floor - video instructions on the Internet will help you see what the process looks like visually, which will give you a better understanding of the essence of the technology. The prepared coating can be used as a basis for application decorative materials, or left as an independent gender.