Deciphering error codes and malfunctions of Ballu air conditioners. Common error codes for air conditioners Error e9 split system
Both domestic and industrial air conditioning systems, for the most part, have self-diagnosis function. This function can work in automatic mode or in a special mode if there is a problem with the equipment. As a rule, information with error codes can be observed on the displays located on the indoor units of the split systems. Thanks to this data, malfunctions due to which malfunctions in the air conditioning system have occurred are precisely determined. To independently determine the causes of problems in devices different manufacturers you can use the lists of error codes for various air conditioners, provided below by brand name.
In LG air conditioning systems, the microprocessor, when a malfunction is detected, blocking the start of the unit, after which it gives signals by flashing the LED, which report the error code.
If the system has detected several problems, then the breakdown that has the smallest sequence number is induced first. After that, there is an indication of faults in ascending order. The table below shows the error codes for LG air conditioners and explains what each of them means.
You should know: the occurrence of similar errors can be triggered by unsatisfactory parameters electrical network, or an accidental failure that occurred in the electronics of the unit. Therefore, do not rush to immediately contact the service, but simply turn off the device and check electrical voltage. It is also necessary to make sure that the correct device operating mode. After these checks, you can turn on the machine. Most often, this method helps in solving this problem, and it no longer appears.
The set of symbols for faults detected by the microprocessor depends on the model of the unit. For LG air conditioners, there may be another indication - in the form of numbers and letters.
Evaporator unit faults:
Capacitor block defect designations:
Designations in LG Art Cool units:
Daikin
Daikins are pretty sophisticated equipment(from a technical point of view) and, in addition to the refrigeration unit, have electronic control boards, many various sensors and valves, power inverter and other components. If any component of the device fails, it is difficult to find the cause of the breakdown without a special function that allows you to diagnose the equipment. This procedure is carried out using the remote control, and error codes Daikin air conditioners in case of malfunction of the device can be seen on its display.
Daikin evaporator unit problems:
Faults in the system:
Other problems:
Panasonic
Panasonic air conditioner error codes are usually displayed on display located on the wall-mounted (room) unit of the unit. They can be recognized by pressing the “CHECK” button on the remote control and holding it for at least 5 seconds.
Since only a hole is visible instead of a button on the remote control, you can use a paper clip to press the recessed button, if it is straightened, or a small carnation.
After the remote control enters the error checking mode of Panasonic air conditioners, point it towards the indoor unit of the device and by pressing the buttons designed to control the timer (“up” and “down” arrows), start to cycle through the codes, starting from “H00” and further, by order. If the fault code matches in the memory of the wall unit and on the remote control, you will hear sound signal. To exit the check mode, press the “CHECK” button again.
Explanation of values for Panasonic units:
Toshiba
The remote control of Toshiba Ras cooling systems also has a “CHECK” button that activates the self-diagnosis of the unit.
Fault codes in household systems Toshiba air conditioners (Toshiba RAS-07S3KHS-EE / RAS-07S3AHS-EE, Toshiba RAS-10EKV-EE / RAS-10EAV-EE):
Also, these values are applicable for RAS-10SKHP-ES, RAS-13SKHP-ES, RAS-13S2AH-ES, RAS-07S2AH-ES, RAS-10S2AH-ES, RAS-07SKHP-ES and others.
Toshiba Industrial Conder Trouble Codes:
ballu
Ballu air conditioner error codes, as usual, are displayed on display evaporator indoor unit. Each time Balu's climate control equipment is turned on, the microprocessor performs a self-diagnosis of the equipment and, in case of problems, displays special symbols on a miniature screen.
Decryption for devices brand Ballu:
Gree
If, when the air conditioner is turned on, the self-diagnosis system detects a malfunction in any module of the device, then its start is instantly blocked. At the same time, all error codes of Gree air conditioners can be observed either on the screen of the remote control or on the display of the indoor unit of the unit.
List of malfunctions of Gree air conditioning units:
General Climate
Alphanumeric designations of problems that are highlighted on the remote control:
Errors that are displayed on the wall unit display(domestic) General Climate:
Some of the General Climate air conditioner error codes above allow the user to independently find the problem and fix it. In other cases, for example, if the def / fan (pre / def) indicator flashes, specialist assistance is required.
Samsung
To start self-diagnostics of Samsung equipment, you need to start the operation of the conder in test mode. To do this, hold the split system start button for 5 seconds. Error codes for Samsung air conditioners, when detected, are displayed on the display of the unit located indoors.
Malfunctions in the operation of Samsung split systems:
Mitsubishi
For troubleshooting in technology from Mitsubishi, it is necessary within 4 seconds. hold on the remote control (simultaneously) 2 buttons: “CHECK” and “SET”. If problems are found, air conditioner error codes Mitsubishi Electric displayed on the display of the indoor unit or remote controller.
In addition to the above errors of the Mitsubishi Electric air conditioner, there are generic error codes related to different models Mitsubishi Electric units:
- error E6 or EE - problems were detected in the connection between the unit located outside and the indoor unit. There is no signal from the sensor, or a short circuit is detected;
- code E5 - malfunctions were detected during the operation of the equipment, it is also necessary to check the electrical voltage in the network.
Hitachi
The tables below show the error codes for Hitachi air conditioners. In Hitachi units, malfunctions are determined by blinking indicators.
TCL
Error codes in TCL climate systems (air conditioners) can be deciphered using the table below (the number of LED flashes in 8 seconds means an error code).
ideas
In Idea units, all problems detected by the processor at startup are highlighted on the air conditioner display.
AUX, DAX, Renova, JAX, Pioneer, Hansa, Saturn, Rolsen, Yamatsu, Daihatsu(Daihatsu), Vitek, digital display for air conditioner series fault:
- Display mode = E4
- Priority level display = 1 Non-mitsubishi52_63_71he-s power supply failure = Plastic temp sensor is abnormal.
- Display mode = E1 Priority level display = 2
- Power supply failure = Copper temperature sensor abnormal (indoor) Display mode = E3 Priority level display = 3
- Power supply failure = Copper temperature sensor abnormal (open, no signal) Display mode = E2 Priority level display =
4
2. H series, AUX, DAX, JAX, Pioneer, Hansa, Saturn, Rolsen, Yamatsu, Daihatsu(Daihatsu), Renova (except KFR-25G/H) h3 HA HB series fault display:
- Power supply failure = PG feedback engine abnormal
- Priority level display = 1 Power supply failure = Plastic temp sensor abnormal Display mode = Timer LED blinks 1 time every 8 seconds
- Priority level display = 2 Power supply failure = Copper temperature sensor abnormal (indoor) Display mode = Timer LED blinks 2 times every 8 seconds
- Priority level display = 3 Power supply failure = Copper temperature sensor abnormal (indoor) Display mode = Timer LED blinks 1 time every 1 second
- Priority level display = 4
3. Series H (Y) air conditioner model remote display, removable panel AUX, DAX, JAX, Pioneer, Vitek, Hansa, Saturn, Rolsen, Yamatsu, Daihatsu:
- Power supply failure = Motor feedback PG abnormal Display mode = Timer LED blinks 4 times every 8 seconds Priority level display = 1
- Power supply failure = Plastic temp sensor. abnormal Display mode = Timer LED flashes 1 time every 8 seconds Priority level display = 2
- Power supply failure = Copper temperature sensor abnormal (indoor) Display mode = Timer LED blinks 2 times every 8 seconds Priority level display = 3
- Power supply failure = Copper temperature sensor abnormal (open, no signal) Display mode = Timer LED flashes 1 time every 1 second Priority level display = 4
4. E. E. E. EU EZ EAA EAD EL HS1 HSZ HL1 HLZ P P1 ZZ CZ digital display air conditioner series AUX, DAX, Renova, JAX, Pioneer, Hansa, Saturn, Rolsen, Yamatsu, Daihatsu(Daihatsu), Troubleshooting:
AUX, DAX, JAX, Pioneer, Vitek, Hansa, Saturn, Rolsen, Yamatsu, Daihatsu power supply failure = Motor feedback PG abnormal Display mode = E4 Priority level display = 1
E1 or EL - as a common nutrition mistake.
Power supply failure or, in Russian, mains voltage< 210 В (сработала защита – токовая нагрузка) = Датчик темп ненормально Режим отображения = E1 Отображение уровня приоритета = 2
E1 - pretty common mistake, just yesterday I encountered.
- The reasons for E1 are obvious - insufficient voltage in the network< 210 В. При пуске компрессора происходит дополнительная просадка напряжения, токовая нагрузка max.
- Power supply failure = Copper temperature sensor abnormal (indoor) Display mode = E3 Priority level display = 3
1
1
5. All other E series except EA EU E.M.E.U.Z. EAA EAD:
Power supply failure = PG motor feedback abnormal
Display mode = Timer LED blinks 4 times every 8 seconds
Priority level display = 1 Power supply failure = Plastic temp. abnormal Display mode = Timer LED blinks 1 time every 8 seconds
Priority level display = 2 Power supply failure = Copper temperature sensor abnormal (indoor) Display mode = Timer LED blinks 2 times every 8 seconds Priority level display = 3
6. QA QB QD digital display of AUX, DAX, JAX, Pioneer, Hansa, Saturn, Rolsen, Yamatsu, Daihatsu, Vitek, Renova air conditioners - malfunctions, error codes:
- Power supply failure = PG motor feedback abnormal Display mode = E4
- Priority level display = 1 Power supply failure = Plastic temp sensor abnormal Display mode = E1
- Priority level display = 2 Power supply failure = Copper temperature sensor abnormal
- Display mode = E3 Priority level display = 3 Power supply failure = overcurrent oprotection
- Display mode = E6 Priority level display = 4
1
1
7. QC QQ light display air conditioner series fault:
- Power supply failure = PG motor feedback abnormal
- Display mode = Timer LED blinks 4 times every 8 seconds Priority level display = 1 Power supply failure = Plastic temp sensor abnormal
- Display mode = Timer LED blinks 1 time every 8 seconds Priority level display = 2 Power supply failure AUX, DAX, JAX, Pioneer, Vitek, Hansa, Saturn, Rolsen, Yamatsu, Daihatsu = Copper temperature sensor abnormal
- Display mode = Timer LED blinks 3 times every 8 seconds Priority level display = 3 Power supply failure = over current oprotection
- Display mode = Timer LED blinks 6 times every 8 seconds Priority level display = 4
1
1
8. Display faults of 18000BTU ~ 24000BTU, AUX, DAX, JAX, Pioneer, Hansa, Saturn, Rolsen, Yamatsu, Daihatsu, Renova series - wall mounted air conditioner series:
- Numbers for digital tube displays:
- Power supply failure = PG motor feedback abnormal
- Display mode = Timer LED blinks 1 time every 8 seconds Priority level display = 2
- System errors = turns off Power supply failure = Plastic temp sensor abnormal Display mode =
- Timer LED blinks 2 times every 8 seconds Priority level display = 3 System errors = turns off
- Power supply failure = Copper temperature sensor abnormal Display mode = Timer LED blinks 8 times every 8 seconds Priority level display = 4
- System errors = not turning off Digital tube displays: Power supply failure = PG motor feedback abnormal Display mode = E1
- Priority level display = 2 System errors = turns off Power supply failure = Plastic temp sensor abnormal Display mode = E3
- Priority level display = 3 System errors = turn off Power supply failure = Copper temperature sensor abnormal Display mode = E2 Priority level display = 4
- System errors = does not turn off
Air conditioner diagnosticsThis is the first thing to do before servicing or repairing it. Diagnostics of the air conditioner allows you to identify breakdowns and malfunctions in the system. Whether it is a lack of refrigerant that needs to be replenished, errors in the operation of the air conditioner, or malfunctions of the main components. Timely and competent diagnostics of malfunctions will allow the service engineer to quickly and efficiently eliminate malfunctions. So, to return a healthy microclimate to the client's home or office. All modern air conditioners have a developed self-diagnosis system. As a result of analyzing the state of the equipment, the system identifies the cause of the malfunction and displays the error code on the display (of the remote control, board or mode indicator). Below are the error codes of air conditioners (alarm code) of various brands. Using this information, you can independently read the error code and repair the air conditioner. This will significantly save the time of equipment diagnostics and avoid inaccuracies in determining the nature and location of the breakdown. Air conditioner error codesWe have selected for you information about error codes for air conditioners and split systems of different brands.
Error codes for Beko BKN, AKN air conditioners⊕ - blinking, 2 - on, 3 - off. If there are these errors, the operation of the air conditioner will be automatically terminated. Error codes for Beko AKH, AKP, AS, BKH, BKP, BS air conditionersError codes for Beko inverter air conditioners BKC 090 INV, BKC 120 INV, BKL090 INV, BKL120 INV
Error codes for Carrier air conditionersIf a malfunction is detected, the green indicator (P) and the orange indicator (R) flash at a frequency of 0.1 seconds, indicating a fault code. It should be noted that the orange indicator (R) corresponds to the tens in the number - the fault code. The green indicator (P) corresponds to the units in the number - the fault code. For example, fault code 13. Orange LED flashes once, both LEDs are off for 2 seconds, green LED flashes three times at 0.5 second intervals, both LEDs are off for 4 seconds.
Error codes for Chigo air conditioners
Error codes for Daewoo air conditioners
Error codes for Fujitsu General air conditionersFujitsu General Ltd. introduced to the market New Product for diagnostics of split systems and multi-split systems GENERAL. The tool is a set of adapters connecting outdoor unit with a computer, and a PC program. With their help, a specialist conducting equipment diagnostics can see in real time the parameters of the compressor, fan motor, EEV, sensor readings, as well as an error log. In the process of testing, it is possible to record a work log with the issuance of a report. The adapter is suitable for working with multi-split systems, as well as with most inverter split systems (wall, ceiling, channel, cassette). Modern Fujitsu General air conditioners have a very advanced self-diagnosis system, according to the results of which the control system, when a particular malfunction is detected, blocks the operation of the entire device and at the same time reports the cause of the malfunction. The Fujitsu General air conditioner control system reports any malfunctions by flashing an LED on the panel of the indoor (in some cases outdoor) unit. When a particular malfunction of the air conditioner is detected, the LEDs light up or flash in a certain sequence, which corresponds to the detected error. If the air conditioner control system has detected more than one error, then the malfunction with the highest priority is displayed first, and then all the others. Error codes for Fujitsu General air conditioners are shown in the table.
For some models (see list *), depending on the error, the OPERATION, TIMER, SWING indicators work according to the following principle: ABOUT- fast blinking; X- slow blinking; - OFF * Внутренний блок: ASG18FBAJ, ASG18FBBJ, ASG18UBAJ, ASG18UBBJ, ASG24FBBJ, ASG30FBBJ, ASG18FBBX, ASG18UBBN, ASG24FBBN, ASG24UBBN, AWG18FBAJ, AWG18FBBJ, AWG18UBAJ, AWG18UBBJ, AWG24FBBJ, AWG24UBBJ, AWG30FBBJ, AWG30UBBJ, AWG14UBBJ, ABG14FBBJ, ABG14FBBJ, ABG18FBBJ, ABG18FBBJ, ABG181BBJ, ABG181BBJ, ABG24FBBJ, ABG24FBBJ, ABG241BBJ, ABG241BBJ, AWG24FBAJ, AWG24UBAJ.
Error codes for Haier air conditionersRepair of air conditioners HAIER (HAYER) is carried out on the basis of an analysis of the operating parameters of devices and fault codes. If there are no errors or malfunctions, but the unit does not start, the start conditions may not be as required. In this case, the following standby codes will be displayed on the display of the head unit: Error codes and malfunctions of indoor units of HAIER air conditioners
Error codes and malfunctions of the inverter outdoor unit
The tables show only some of the HAIER air conditioner trouble codes. We remind you that HAIER air conditioners are technically sophisticated equipment. Error codes are provided for qualified and certified technicians. That is, for those who are professionally engaged in the repair of HAIER air conditioners, and not for ordinary users. Trust the repair of HAIER air conditioners to professionals.
Hisense Air Conditioner Error CodesIf a malfunction occurs, press the Sleep button on the remote control 4 times - the error code will light up on the 7-segment display (see table below). If there are several errors, then press the Sleep button 4 times again - the LED indicator will light up with the following error code. Updated remote remote control, which has 4 modes of operation of the Sleep button, allows you to set 4 different combinations. When using it to check error codes, you must press the "Sleep" button 10 times. After that, error codes will start to be displayed.
Error codes for IGC air conditionersIMS MINI (IMS-EM080NH, IMS-EM100NH, IMS-EM120NH, IMS-EM140NH, IMS-EM160NH)
Error codes for Kentatsu air conditionersError codes Kentatsu KSVP-HFE2 - room temperature sensor malfunction Error codes Kentatsu KSKT-HF channel typeE0 - Faulty room temperature sensor Error codes Kentatsu KSFU models: KSFU/KSRU76HFDN3, KSFU/KSRU140HFDN3P4 - thermal protection of the evaporator of the indoor unit Error Codes Kentatsu KSGH/KSRHModels: KSGH/KSRH21CFDN1 KSGH/KSRH26CFDN1, KSGH/KSRH35CFDN1 KSGH/KSRH53CFDN1, KSGH/KSRH21HFDN1 KSGH/KSRH26HFDN1, KSGH/KSRH35HFDN1 Kentatsu floor type error codes KSFU70XFAN1 / KSRU70HFAN1, KSFU120XFAN3 / KSRU120HFAN3P4 - evaporator temperature protection
Error codes for LG air conditioners
LGMV is a mobile application developed by the manufacturer for remote monitoring operating parameters of LG air conditioning systems. The application helps engineers assess the current state of equipment. The analysis is based on a multi-year operation cycle. The program helps not only to quickly identify problems in the system, but also gives recommendations for resolving the issue. The LGMV diagnostic system provides monitoring of system operating parameters, prevention and prevention of system malfunctions. All this certainly simplifies diagnostics and commissioning. LGMV consists of a wireless communication module and a free smartphone app. To use the LGMV mobile application, an exclusive Bluetooth module is required, the corresponding connector of which must be connected to the CN-LGMV port on the main board of the outdoor unit. LGMV main features:Visual display of key information about the operation of the air conditioner. Mobile LGMV can be downloaded, for example, from Google Play as a product of LG Electronics, Inc. as a tool for Maintenance, troubleshooting for LG air conditioning systems. Mobile app LGMV uses a limited resource on a smartphone and processes data in real time. Data monitoring may be difficult or data may not be fully saved if the performance of the smartphone is poor. It is recommended to use a high performance smartphone. If system resources are insufficient due to other Internet applications that are enabled, data monitoring may fail in addition to monitoring. The monitoring function and saving function may not work fully. And also Bluetooth communication connection can be disabled. In addition, the application may be disabled due to a lack of resources or an unexpected error. The communication level may increase depending on the number of outdoor and indoor units. Bluetooth transmission distance may be shortened to the point of turning off data transmission depending on the weather or conditions. environment(electromagnetic waves or obstacle), etc. It is recommended to use the Bluetooth module for a short distance.
Error codes for MDV air conditionersError indication on MDV indoor unit
Error indication on external MDV unit
Mitsubishi Electric Air Conditioner Error Codes
Mitsubishi Heavy Air Conditioner Error Codes
Error codes for Wisnow air conditioners
Error codes for Polaris air conditioners
Sanyo Air Conditioner Error CodesDescription of the malfunctions that are indicated on the board of the SANYO W-ECO MULTI SYSTEM outdoor unit. Valid for SPW-CR1503GDYH8, SPW-CR1903GDYH8, SPW-CR703GDCH8, SPW-CR903GDCH8, SPW-C1503GDYH8, SPW-C1903GDYH8, SPW-C703GDCH8, SPW-C903GDCH8.
Sharp Air Conditioner Error CodesFor example, fault indication in SHARP air conditioners models AY-A184E / AE-A184E, AY-A244E / AE-A244E.
Error codes for Toshiba air conditioners
The work performed during the diagnostics corresponds to the work performed during. The only difference is that during the diagnostics, all the main parameters of the equipment operation are checked and recorded, and during the service, the identified deviations from the norm are eliminated. The list of works in the diagnosis of air conditioningDuring the diagnosis of the air conditioner, firstly, an external examination is carried out for the absence mechanical damage. Not only hull, but also hydraulic and electrical parts of the equipment are inspected. In addition, the reliability of the fasteners of the external and internal units is checked. As well as the quality of the clamps of all contact connections of electrical equipment. Before turning on the equipment, it is necessary to check the condition of the air filters. They must be not only clean, but also without damage. After inspection, as a rule, switching to the "cooling" mode is performed. Use the remote control to test the system. During the functional test, the indication of the air conditioner modes is evaluated, as well as the operation of the mechanically driven exit blinds. One of the indirect indicators of the efficiency of the system is the control of the temperature of dry air at the inlet and outlet of the evaporator. With the help of pressure gauges, the average suction / discharge pressure is measured (with free access to the outdoor unit). Of course, it is mandatory to check the tightness of the connection between the indoor and outdoor units. In addition, you need to make sure that there are no leaks in drainage system conditioner. If something went wrongThe specialist can also judge the nature of the malfunction by the “behavior” of the air conditioner. For example, if the air conditioner turns on and immediately turns off, after which an error message is displayed - most likely, the matter is in the sensors (malfunction of the air temperature sensors or the evaporator). If the air conditioner turns on, runs for 15-20 seconds, and then turns off, the indoor unit fan motor is most likely defective (rotation speed is lower than the set rpm). If the air conditioner does not turn on at all and at the same time all the LEDs flash (or do not light up), most likely, a failure has occurred printed circuit board management. Simultaneous flashing of all indicator lamps of the air conditioner, as a rule, means only a failure of the program settings of the control board. Most likely, this is due to the non-compliance with the GOSTs of the network parameters, for example, due to a power surge in the network. It is not difficult to eliminate this malfunction - it is enough just to reprogram the main control board. Since information about codes is provided only to authorized service centers, in this case it is necessary to contact our specialists. Before…If your air conditioner does not work, first of all make sure that the air conditioner is securely connected to the outlet. Check the circuit breaker or fuse on the supply line, if necessary restart the circuit breaker or replace the fuse. Read the user manual again and make sure all modes are set correctly. Doing it yourself will save you money. Because in many cases the engineer you called, after doing what you can easily do yourself, will charge you for the false call. If these steps do not help, then contact the sales organization that sold you the air conditioner. Or contact an authorized service center of the air conditioner manufacturer. Undoubtedly, this is the best, fastest and reliable way restore the performance of your air conditioner. The sales organization that sold the air conditioner should give you information on how to contact them. This information is available not only in the warranty card, but also on the manufacturer's website in the appropriate regional section. Air conditioner test modeTo facilitate diagnostics, modern air conditioners have a so-called test mode. Compared to the operating mode, the air conditioner turns on in cooling mode and does not respond to sensor readings and air temperature. That is, in the test mode, the air conditioner will function as long as it is necessary for the service engineer to study the operation of the system units. After turning off the test mode, the air conditioner will return to normal operation. IN samsung air conditioners a test mode is also provided. To enter the test mode, press the on / off button on the indoor unit and hold it for five seconds. At the same time, the temperature indicator displays the installed software settings option at a second interval, for example, 0b0000-1730F8: 0b00001730F80b (only for models with a temperature indicator). When testing the operation of the air conditioner, the cooling mode is switched on with the following restrictions: Error codes for Baloo air conditioners are required in order to timely identify the malfunction and contact the master to fix it. It should be noted that in some cases the slightest delay becomes critical, so it is better to monitor the appearance of information on the scoreboard. True, the errors of Baloo air conditioners directly depend on the series. Because the hardware is different. software, which means that it informs a person about malfunctions in different ways. So, you should consider all possible codes depending on the series. Mistakes on the example of Ballu MFS2Errors of air conditioners Baloo series MFS2:
The number of codes shows how much information a person receives about the operation of his own equipment. Accordingly, he can turn to specialists at the right time. Below is the maximum full list codes of errors and malfunctions encountered in this technique in general. Errors air conditioner Balu series BSC, BR, BV
It is immediately clear that the last three series have a much smaller number of codes. On the one hand, this shows how stable models are considered. On the other hand, the user receives less information, which often leads to difficult situations and additional diagnostics of cassette air conditioner models. Air conditioner error codes - helpful information that appears on the equipment screen. If you correctly recognize them, you will be able to find out exactly which malfunction should be fixed. Because of this, maintenance takes a minimum of time, which means that the owner does not have to suffer from a lack of equipment.
With Gree air conditioners and split systems, repairs are easier than with hi-fay series models. Self-diagnosis of Gree air conditioners What explains this, the layman asks? The explanation is simple Gree: codes. On Gree air conditioners and split systems, there are not many protection system sensors. Those. everything is simplified.
You will laugh, but for example, the catalog of Supra air conditioners has not even changed the name of the outdoor unit, perhaps there are not enough skills in Photoshop, perhaps they did not consider it necessary. In a word, how were Supra air conditioners certified in Russia? It's a mystery to me. Supra Catalog!! In faith. Heh... Self-diagnosis of Gree air conditioners is, -
Everything, agree not much. Gree, like an air conditioner, is functionally simple, so there are not many error codes. Error codes table, continued. currents during voltage surges. A trifle, but it must be borne in mind when repairing air conditioners Gree and their analogues. Example: country house. The owners, leaving the dacha, usually de-energize the building with a common switch. When the power is turned on with a load, current and voltage surges occur.
There are "specialists" who use wire when burning a fuse. Can you do that? It is possible, but then, in addition to the varistors, the control board, the fan motor of the indoor unit will also burn out, and ... it rushed up to the compressor windings of the outdoor unit of the air conditioner. Fireworks at the cottage. - Expensive repairs. Troubleshooting and breakdowns of the air conditioner, Gree: codes, as usual, we start with ...- refrigeration circuit malfunctions, - malfunctions of the electrical part, system e-mail. power supply and air conditioning control. GREE Semi-industrial, industrial air conditioners, - error codes.Error Code = E1 Error Code = E2 Error code = E3 Error code = F0 Error code = F1 Error code = F2
Error code = F3 GREE Split air conditioners Error code... The cause of the malfunction, - the refrigerant system is highly protected, - pressure. Gree LED blinks 1 time. The cause of the Gree malfunction is frost protection. Air conditioner start LED = LED blinks 2 times. Cause of the malfunction, - Compressor exhaust high temperature protection. Air conditioner start LED = flashes 4 times Cause of malfunction, - AC overcurrent protection Air conditioner start LED = LED blinks 5 times The cause of the malfunction is a communication failure between the indoor unit of the air conditioner and the outdoor unit of the split system. Gree air conditioner start LED = blinks 6 times Cause of malfunction, - Anti-high temperature protection Air conditioner start LED = flashes 8 times Cause of malfunction, - No feedback internal engine fan Air conditioner start LED = flashes 11 times Cause of the malfunction, - Jumper cap faulty protection Air conditioner start LED = flashes 15 times Cause of malfunction, - Closed ambient sensor open, no contact or short circuit Indicator, - cooling = LED flashes 1 time Name of sensor malfunction or failure = Indoor tube open, no contact or short circuit Air conditioning start LED = The cause of the malfunction, - the external ambient sensor is open, there is no contact or a short circuit Air conditioning start LED = Cause of malfunction, - Outer tube sensor open, no contact or short circuit Air conditioning start LED = Name = malfunction or failure of the exhaust sensor open, no contact or short circuit Air conditioning start LED = Cause of malfunction, - Over load limit / frequency reduction Air conditioning start LED = Cause of malfunction, - Over current limit / frequency output Air conditioning start LED = The cause of the malfunction, - High exhaust gas temperature limit / frequency reduction Air conditioning start LED = The cause of the malfunction, - Overvoltage protection for Ru Air conditioning start LED = Cause of the malfunction, - alternating current detection of faulty circuits Air conditioning start LED = The cause of the malfunction, - Compressor reverse protection Air conditioning start LED = The cause of the malfunction, - Over the compressor phase current protection Air conditioning start LED = The cause of the malfunction is the inlet of the malfucntion by the sensor tube Air conditioning start LED = The cause of the malfunction, - The open DC fan motor is defective. Air conditioning start LED = Cause of the malfunction, - Output malfunction or breakage of the tube sensor Air conditioning start LED = The cause of the malfunction, - The compressor overload sensor is defective. Air conditioning start LED = Cause of malfunction - Defrosting Air conditioning start LED = The cause of the malfunction is static dust protection cleaning Air conditioning start LED = Cause of malfunction, - Compressor overload protection Air conditioning start LED = Cause of malfunction, - System abnormal protection Air conditioning start LED = The cause of the malfunction, - IPM protection Air conditioning start LED = Cause of malfunction - PFC protection Air conditioning start LED = Cause of malfunction, - Compressor step loss protection Air conditioning start LED = Cause of the malfunction, - Heating against high frequency temperature drop Air conditioning start LED = Cause of malfunction - Startup failure Air conditioning start LED = Cause of malfunction, - Phase failure protection compressor Air conditioning start LED = Cause of the malfunction, - Phase current compressor faulty detection circuits Air conditioning start LED = Cause of malfunction, - Compressor degaussing protection Air conditioning start LED = The cause of the malfunction, - EEPROM loading is defective. Air conditioning start LED = The cause of the malfunction is a communication failure between motherboard and board drivers Air conditioning start LED = The cause of the malfunction is a malfunction of the charge capacitor Air conditioning start LED = The cause of the malfunction is the IPM of the sensor circuit is faulty. Air conditioning start LED = The cause of the malfunction, - IPM high-temperature protection Air conditioning start LED = Cause of the malfunction, - PN protection voltage drop Air conditioning start LED = The cause of the malfunction is low voltage protection PN Air conditioning start LED = Cause of the malfunction, - The current detection circuit is faulty or the current sensor is faulty or broken Air conditioning start LED = The cause of the malfunction, - Compressor phase failure protection Air conditioning start LED = Cause of malfunction, - Compressor or rotary protection blocked Air conditioning start LED = The cause of the malfunction, - IPM is more than the temperature limit / frequency reduction Air conditioning start LED = Cause of malfunction - 4-way reversal valve abnormal Air conditioning start LED = The cause of the malfunction is the shutdown of the exhaust gas temperature sensor Air conditioning start LED = Cause of malfunction, - AC zero voltage error detection Air conditioning start LED = The cause of the malfunction, - Over the tube frequency temperature difference Air conditioning start LED = Cause of the malfunction, - Anti-freeze limit / frequency reduction Air conditioning start LED = Models: brand air conditioner repair KFR-32GW/BP, KFR-45LW/D, KFR-3502GW/BP, KFR-2501GW, KFR-45LW, KFR-3301GW, KFR-3201GWCPU, KFR-2608GW/BP and other KFR series, PDF fail.
|