Arranging a summer house is a constant process. Either you build something, or you improve it. Moreover, furniture is constantly needed and tables are most in demand in the country. And put it in the garden, and near the house, and also in . We will tell you how to make a table for a summer house with your own hands in this article using the example of ready-made projects.

Homemade table from pallet boards

The material for this table was disassembled pallets. Naturally, you can use new boards. There is only one condition - they must be dry. You can buy dry ones (this costs more) or buy regular ones, put them somewhere in ventilated stacks and keep them for at least 4 months, or better yet, six months. In general, any furniture, including, is made from dry wood.

We are assembling a table for the street - to put it in a gazebo, so we will not glue the boards of the tabletop, but will fasten them from below, using planks. It's very simple country table and very cheap.

Having disassembled the pallets, we get boards with individual colors and patterns. Having worked a little magic, rearranging them several dozen times in different ways, we achieve the required result. It turns out to be quite a nice tabletop.

Take the side parts of the pallet. We use them for the table frame. We first sand them with coarse sandpaper, then fine sand them to the required smoothness (grain 120 and 220).

We take the planks that remained unused and use them to fasten the tabletop. We place them in the place where the joints of the boards are located. We use two self-tapping screws to fasten each board with a joint, and one for a solid one.

From the treated sidewalls and two boards (also sanded) we assemble the table frame. We fasten its parts with self-tapping screws at the end (two for each joint). The frame can be glued or also “planted” on self-tapping screws. Only they are long. For each, we pre-drill holes with a drill whose diameter is slightly smaller than the diameter of the screws.

We turn the assembled tabletop over and sand it. The procedure is the same - first use sandpaper with coarse grains, then with fine grains.

Next is installing the legs. Selecting four boards same size, check their length and adjust if necessary. Then - sanding again. This is easier than sanding the legs that are already screwed on. We screw the sanded boards to the frame. These will be the legs. For each there are two self-tapping screws, fixed diagonally (look at the photo). For greater stability, we install jumpers at the bottom. You can leave about 10 cm from the floor to the lintels. We connect everything with self-tapping screws, so that the boards do not crack, we pre-drill holes.

After removing the dust, varnish again. In theory, the varnish should lie flat, but it depends on the wood, so another sanding/painting cycle may be needed. As a result, we get this homemade country table.

If you don’t like mismatched boards and traces of old nails, you can make the same design into boards. This table can be rectangular, or square. All sizes are arbitrary - please see the space available.

Country table made from leftover boards

This DIY garden table is assembled from the remains of boards of different types and sizes. We went to the tabletop frame pine boards 25 mm thick and 50 mm wide, leftovers for legs are 15*50 mm. We make the frame according to the dimensions you need. This table will stand on the veranda, which is small in width. So let's make it narrow - 60 cm, and length 140 cm. The height of the legs is 80 cm (everyone in the family is tall).

Immediately cut off two long boards 140 cm each. To make the tabletop width 60 cm, subtract twice the thickness of the board used - this is 5 cm. Short bars should be 60 cm - 5 cm = 55 cm. Fold the frame, following right angles, twist with self-tapping screws. We check whether the bars are folded correctly - we measure the diagonals, they should be the same.

We cut the boards into four 80 cm boards and attach them from the inside to the assembled frame. You can use 4 screws for each leg.

At approximately the middle of the height of the legs we attach the crossbars. This is a frame for a shelf. The shelf can be used for its intended purpose, and it also increases the rigidity of the structure. We fasten strictly at right angles, checking with a large square.

We put the frame on the floor and check whether it wobbles or not. If everything is done correctly, it should stand rigidly. Next, take sandpaper or a sander and sand.

Let's start assembling the tabletop. From finishing works There were boards of different types of wood left, some painted with stain. We alternate boards of different colors.

We fasten the tabletop boards with finishing nails, carefully finishing them off with a hammer. You can secure it to the shelf with regular nails or self-tapping screws. Then we smooth it out with a sander. Last stage- painting. Very unlucky with the choice of varnish. Bought too dark appearance didn't like it. I'll have to sand it again and paint it a different color.

Wooden table with glued top

This design features L-shaped legs. They are assembled from boards of the same thickness. IN in this case 20 mm. In order for them to hold well, 5 self-tapping screws are needed. We pre-drill holes with a drill with a diameter 1-2 mm smaller than the diameter of the screws. Then with a drill larger diameter drill holes for the caps. The diameter can be matched to furniture plugs of a suitable color or made from a wooden rod. Another option is to use wood putty, to which you add wood dust that remains after sanding. After drying and sanding, the marks will be difficult to find.

When assembling the legs, you must ensure that the angle is exactly 90°. You can choose timber as a pattern. First, coat the joint of the two parts of the leg with wood glue, then install the screws in the following sequence: first the two outer ones, then the middle one, and only then the other two. After the glue has dried, we sand the legs, varnish them and dry them.

It's time to make the tabletop. We assemble it from boards of the same thickness. Choose the size you need. You can use fragments of different widths. It is only important that everything looks organic, and that the sides of the boards are smooth and fit together without gaps.

Coat the sides of the boards selected for the tabletop with glue and lay them on flat surface(some kind of table) and tighten it with clamps. In this case, we got by with one, but preferably at least three. We tighten it so that there are no gaps in the resulting shield. Leave it for a day. Having removed the clamps, we get an almost finished tabletop. It still needs to be trimmed - to align the edges, and then sand it. You can trim with a jigsaw or a regular hand saw. It's difficult to get a straight line using an angle grinder, but you can try. After sanding we get a beautiful tabletop.

Using the same technique, you can make an oval or round tabletop. You just need to draw the appropriate line and trim the glued boards along it.

To make the table look more attractive, we will make a frame. We take a thin strip, sand it with sandpaper and fasten it around the perimeter of the tabletop. You can also use finishing nails. Only we also first coat the planks with wood glue, and then with nails.

After the glue has dried, we sand the joint again with sandpaper.

Now you can attach the table legs. We assemble a table frame from four boards (there is no photo, but you can do it as in the previous paragraph). We attach it to the back of the tabletop with glue, then install it through the tabletop furniture confirmations. A preliminary hole with an extension for the cap is drilled for the confirmations. The holes for fasteners are masked in the same way as on the legs.

We attach the legs to the fixed frame. We place them inside the frame. You can attach it with regular self-tapping screws. That's it, we made a table for the garden with our own hands.

How to make a garden table from wood with benches

For this table we used 38*89 mm boards (we unraveled them ourselves), but you can take standard sizes. A difference of millimeters will not greatly affect the results. In the photo below you can see what should happen.

To connect the parts, 16 cm long studs with washers and nuts (24 pieces) were used. All other connections are made with nails 80 mm long.

The parts are installed in place, a through hole is drilled with a drill. A stud is installed in it, washers are put on both sides and the nuts are tightened. Everything is catching up wrench. Why is this option convenient? For the winter you can disassemble it and take it to a barn or garage.

Making seats

According to the drawing, we cut the boards to the required size. Everything is needed in double quantities - for two seats. We sand the boards, special attention pay attention to the ends.

The short sections that we use to fasten the three boards of the seat along the edges are cut at an angle of 45°. First, we assemble the structure that is attached to the seat from below. We take a board about 160 cm long, and attach two short boards sawn at an angle to the end of it. You need to attach it so that this board is in the middle.

Then we attach the legs to the resulting structure (you can use nails). Then we add more boards cut at an angle and tighten everything with studs and bolts.

We attach the seat boards to the resulting structure. Since this is an outdoor table, there is no need to knock them together closely. Leave a gap between two adjacent ones of at least 5 mm. We nail it to the supports (which have been sawn down), two for each board.

We fasten the finished seats using four boards 160 cm long. We fasten each leg with hairpins (if you walk, you can put two hairpins, installing them diagonally or one above the other).

Assembling the table

The table is assembled according to a different principle. Please note that for the tabletop, the transverse boards along the edges are cut at 52°. We attach them at such a distance that the legs fit in. 2 nails for each board. You can use finishing ones, with small heads, or you can drive them deep and then mask the holes with putty.

Now we need to assemble the cross legs. We take two boards, cross them so that the distance between their ends is 64.5 cm. We outline the intersection with a pencil. At this point you will need to remove the wood to half the thickness of the board.

We make the same notch on the second board. If you fold them, they turn out to be in the same plane. We connect with four nails.

We make the second leg for the table in the same way. We are not assembling the table yet.

Installing the table

Now you need to attach the legs to the structure on which the benches are installed. We put them on equal distance from the benches, fasten with pins.

Now we install the tabletop. We also fasten it with pins. The last stage is painting. Here everyone does as he pleases.

Variations on a theme

According to this drawing, you can make separate benches and a table for a summer house or garden. The design is reliable and simple to implement.

DIY garden table: drawings

We will send the material to you by e-mail

Not everyone likes to buy ready-made products for home use. The soul of some people requires creative and practical self-realization. The editors of the online magazine website invites those interested to learn how to make a wooden table with their own hands, what is required for this, and whether there are any pitfalls in such work.

Beautiful wooden product for the kitchen or living room, made with love

Professional carpenters are unlikely to find our step-by-step recommendations, but for novice amateurs the advice will come in handy. First, let's look at what products you can make with your own hands from wood.

Of course, the more skills a person has, the more complex the model he can make. But to build a table with your own hands from wood, there are ready-made drawings and photos to help beginners.

How to choose a material for making your own wooden table for home and garden

What to make your own dining table from? Best of all - made of wood. The most pliable wood for a new master will be pine. Products made from poplar will look more solemn. For the street you can take mahogany.

If you want a simpler option for your home, then you should consider laminated chipboard with optimal thickness at 25-35 mm. On the tabletop you can take wooden boards, birch plywood with a thickness of 35 mm. Legs can be made of metal or wooden beam(about 50 mm thickness).

In order not to make a mistake with the amount of material, a preliminary drawing of the future structure is made with precisely specified dimensions.

Advice! The suitable height of the product varies between 750-800 mm.

Related article:

DIY furniture made of wood: for the garden, children's room, kitchen, bathhouse, garden, gazebo; How to restore pieces of furniture, useful tips and recommendations from experts - read in our publication.

What tools are needed to make a wooden table with your own hands?

It doesn’t matter what shape the future table will be: working with wood requires a certain set of tools. You can't do without a jigsaw, and it will be much easier to work with an electric model. To secure all structural elements, use either a drill with a multi-stage drill for holes, or confirmations. To polish the product to perfection, you need a special attachment for a drill.

For greater fastening strength, the tools include wood glue.

How to make a wooden table with your own hands - step-by-step instructions

We have selected four types of structures that can be made on your own, even with a minimum of carpentry skills. We invite you to learn about the stages of manufacturing round and rectangular table, coffee table and models for garden gazebos.

Making a wooden round table

It is easiest to make a round table top and a connecting ring from or with dimensions of 1500 × 1500 mm and 1280 × 1280 mm. You will also need two laminated chipboard strips (1110 × 120 × 25 mm). The legs will be made from four wooden blocks measuring 120 × 50 × 750 mm.

How to make a countertop

How to draw a circle perfectly straight? Place your own thumb on a sheet of plywood in the center with a string and pencil tied to it. The length of the rope from the base to the top should coincide with the radius of the future tabletop. Holding your finger in one place, draw a circle around the full length of the rope with a pencil. All that remains is to cut it out with a jigsaw.

The underframe circle is cut out in the same way.

Making legs

A round table made of wood or chipboard will look charming if you do everything consistently. You won’t have to bother with the legs if your plans aren’t too original. The bars are divided into 4 parts according to the desired size of the table height minus the thickness of the tabletop. First, one leg is cut off, and the other three are aligned along it.

All processing grinder is carried out immediately.

Advice! You shouldn’t rush into sanding, as the first coat of varnish will reveal all the imperfections.

Assembly of the structure and processing of the finished product

Assembly is carried out in stages. First, align the planks groove to groove. Then the crosspiece of the planks is connected to the legs with confirmations, as in the figure below:

If you want to make the structure stronger, before connecting the legs to the tabletop, coat their upper base with glue.

Advice! Nails are not used in this type of work: a self-tapping screw or confirmat can be unscrewed without any problems, and the connections will be much stronger.

Making a rectangular wooden kitchen table

The rectangular design is classic and very useful in everyday life: it is convenient to cook on such a table and you can comfortably dine at it.

How to make a countertop

A wooden tabletop for a table is made either from a whole sheet of plywood, or from individual edged boards processed to perfect smoothness.

Having fastened the boards with screws and glue, they begin to make the frame.

Making wooden legs for a table and frame

At the heart of the quadrangular models is a frame. It serves to securely fix the legs, ensuring the stability of the entire structure. The tabletop is turned over, a depth of 3-4 cm is measured on each side and the measurements are transferred to the boards. As a result, you will need two boards of shorter length and two longer.

The frame is made of four elements: according to the approximate ratio, these are two boards of X cm and two of 2X cm. They are connected to each other with an overlap one after another, building a rectangle. In order not to break the 90° angle, use any board when working with a screwdriver: it is used to press the structure while tightening the screws.

As soon as the frame box is ready, they begin to make the legs. You can take ready-made balusters for the table, buy metal supports or cut them out of bars according to the desired length according to the drawing.

Both the frame and the legs are subject to mandatory thorough sanding!

Product installation and final finishing

The frame is screwed to the tabletop with glue or self-tapping screws. Then the product is turned over and the legs begin to be attached.

Important! It's better to make holes for the screws in advance. This eliminates the possibility of the wood splitting.

Why don't they use nails and a hammer? Not everyone has the skills to work with a hammer - it’s not only dangerous to hit your finger. Overdoing it can easily damage the wood by splitting it. Confirmations and self-tapping screws hold the tree much more firmly.

As soon as the leg is secured, the angle is immediately checked: there should be no deviation from 90°. The operation is repeated with other legs. You can attach the legs directly through the tabletop, but this will affect the aesthetic component of the product.

Related article:

: photo best ideas. What can be made from pallets for an apartment, office and cottage; rules for selecting and processing pallets; Master classes on making a table, sofa, bench, armchair and shelving - read our publication.

Making your own wooden coffee table

Not only beautiful element interior, but also useful. There is no need to look for a visible place to put a book, gadget, glasses, or TV remote control. Such necessary designs made from different materials: metal, glass, plastic, chipboard, wood. But let's leave other materials alone and concentrate on working with wood.

Choice wooden table top for the table depends on the expectations of the owner of the product. Some people want something massive, while others prefer lighter options. Let's stick to a simple solution.

We purchase five boards 30 × 150 mm and process them to perfect smoothness. Immediately saw off the required length onto the tabletop: you should get 6 identical sheets. We take four bars for the legs, 6 shorter pieces for the lower tabletop, and 4 narrow slats for the frame.

Illustration	Description of action
	To brush wood, use a grinder with a brass brush attachment. The procedure will expose the structure of the wood, giving the product a special flavor.
	We go back and forth along each board on the side that will be the front.
	We treat the wood with fire. The flame is gradually moved from place to place: the board will acquire a beautiful darkish tint. The procedure will completely destroy unnecessary soft wood fibers. We actively wipe the entire surface with a felt boot or a piece of felt.

Let's start the assembly process small table with your own hands made of wood.

1. The lower and upper tabletops are laid on work surface wrong side towards you. The boards are laid tightly together, gluing them together. Once the boards have set, slats are attached to the top tabletop. They will serve as a frame and fastening element. They can be glued or screwed with self-tapping screws. The self-tapping screw is screwed into the center of the slats into each of the boards.
2. The legs are screwed to both the tabletop and the slats. You can use furniture corners.

Video: the process of making a coffee table from wood

Making your own wooden table with benches for a gazebo

It's time to take the time and build a wooden garden table.

It is best to take standard size boards. IN hardware store Studs (suitable with a length of 16 cm), washers (24 pieces) are purchased. For a garden gazebo, long nails (8 cm) will do.

Whether to paint a product or simply varnish it is a matter of taste.

Often, to create something new, we need advice from other people. Have you ever made furniture for your home yourself? Today we’ll talk about how to make a wooden garden table with your own hands. The variety of tables is so great that when making a desk or dining table there are their own nuances. But there is also general tips, which may be useful when creating this piece of furniture. There are several important aspects, which should be primarily taken into account in this work.

• choose the right wood;
• choose the right configuration for your desk;
• create a drawing and mark on it necessary details and features.

The tree classification can be structured as follows:

1. Soft type: pine, spruce, fir, cedar and other woods.
2. Hard type: oak, birch, beech, ash, maple, walnut, fruit tree wood.
3. Very hard type: boxwood, yew, dogwood, birch wood

According to the needs of different people, as well as in the case of individual distinctive situations, it is important different characteristics wood or its features:

1. Rot resistant.
2. Texture of the material.
3. Price of raw materials.

If your goal is to make furniture for a living space (and not just practice a skill), then you need to take into account the quality of materials without neglecting them. Dry lumber must be used. How it will be dried is up to you. Assess in advance whether you can properly dry the wood at home; if this is not possible, it would be more profitable and reasonable to order already ready material. During drying, the wood will be deformed, this must be taken into account, but purchasing already dry wood is much more expensive. For high-quality drying at home you will need:

• constantly stable temperature regime, otherwise the material will dry in waves;
• good ventilation in the room, no draft;
• It should be remembered that this process is very long; the material must be dried without being shifted from place to place for about six months.

1. Tabletop.

Here important role strength plays a role, as well as the absence or low absorption of moisture by wood. Optimal material: pine, oak. For a pine countertop, choose a cheap one, but quality material– without rotten areas, cracks, protruding knots and other unnecessary defects.

1. Table legs.
   

Optimal material: birch, it is durable enough for constant load, boxwood and acacia are also suitable.

To make a table from wood, the material must first be treated with sandpaper. If you are just starting your carpentry career, it is worth using birch, pine, oak, acacia and boxwood in your work.

There are several advantages when using wood in construction:

• easily subject to various processing;
• sufficiently resistant to changes in temperature and humidity;
• good shock absorption: practically no chips or scratches;
• simply undergoing restoration;
• environmentally friendly material;
• the cost varies depending on the type of wood and processing methods;
• the material is easy to saw, cut, chip special tools;
• does not require careful and constant care
• external aesthetics.

That being said, there are some significant disadvantages to keep in mind:

• the cost is significantly higher compared to other materials;
• wood can become deformed under the influence of weight;
• without the use of special coatings it is not resistant to mold and mildew, corrosion;
• wood cannot be called a moisture-resistant material;
• Over time, the above aesthetic appearance may be significantly lost.

Wooden tables: range of shapes and sizes

It is important to decide in advance what shape and configuration the table requires. Professionals advise paying attention to several points:

• the table should fit well into the room where it is planned to be installed;
• think about how many people will constantly be at this table and what it will be used for; from this parameter, calculate the size of the product;
• choose a folding table option if from time to time you need it for more people;
• take into account the age and capabilities of people (for example, the table for children will be different).

The table may be different shapes. Besides various shapes, the table can also have different support under the tabletop itself, in other words, different quantities legs

• table with one leg - this type of installation is suitable only for a small product; it can be used, for example, to make a children's table;
• table with two stable legs - this type of table is good for a rectangular or oval tabletop, but is quite inconvenient and unstable for constant use in everyday life;
• a table with four legs is the most common type, has the greatest stability (compared to the others), is suitable for both a dining table and a coffee table - it is the most versatile type of this type of furniture.

In order to guess the most suitable table size for any room, you should always take into account and keep in mind the area of ​​the room itself and that part of it that is the maximum permissible for placing this piece of furniture; you should also, of course, take into account the wishes of the owners.

Features of assembling wooden tables

There are several types hand assembled wooden tables.

• o on dowels (attached with glue);
• o on the drawers (necessary on tables that are subject to periodic disassembly);
• o bolted (such connections are used mainly for garden furniture).

Woodworking workshop and tools

1. Room

There are several characteristics that are necessary when organizing your own workshop:

• work should be carried out under some kind of canopy, ideal option: garage or barn (otherwise there will be too much dependence on the weather);

1. it is necessary to make a high-quality hood, otherwise dust will constantly settle on finished product and you will not achieve straight lines or high-quality finishing of the material. In addition to dust, the hood allows you to eliminate the toxic smell of varnishes and wood paints.

Tools

• an electric jigsaw gives greater accuracy in cutting wood than a saw;
• rotating miter box facilitates corner cutting;
• The sanding machine is universal in use and will obviously be required for the manufacture of wooden furniture;
• a manual router is required when processing holes;
• impregnating and other compositions.

Consumables for working with wood: varnishes, paints, impregnation, glue

• used motor oil – great option for impregnation, but, unfortunately, not suitable for the dining table;
• it would be optimal to impregnate with a water-polymer emulsion twice, with a break of three to five days;
• acrylic varnishes on water based superior to old furniture nitrocellulose varnishes;
• PVA has been proven to be superior to bone wood glue.

Options for wooden tables

1. Wooden table with benches.

• You need to assemble the table top: the boards are attached to the crossbars with self-tapping screws (it is important to use self-cutting screws as opposed to nails, since the latter contribute to the destruction of the wood surface).
• After this, the legs are attached to the crossbars, which must be strong and durable in order to withstand the weight of the table itself and the people sitting at it placed on them, thus minimum thickness will be 4 centimeters).
• Then you need to attach the side crossbars to the legs, on the basis of which benches should be built, fastening them with bolts rather than screws for greater strength.
• Next, we secure the benches and proceed to the subsequent processing of the furniture.

There are several disadvantages to this invention that must be kept in mind:

• If a person on one side suddenly stands up, then all the food will literally fly towards the other.
• It is also not very comfortable to sit at this type of table.

You can improve this design To make its quality unsurpassed, we invite you to evaluate the idea and project!

1. Table made from pallet boards.

If you have boards at your disposal different sizes, colors and, perhaps, even tree species, you can make an interesting design out of them by organizing the elements in a special way: alternating, grading, creating your own logic for constructing the boards. Among other things, also use discarded dry boards. The side parts of the pallet can act as a good frame, and the rest can be used as a tabletop. We recommend this work in the yard or garage with an exhaust hood due to large quantity dust settling everywhere.

• For the legs, use timber more than five centimeters thick. Pre-prepare all the tools and parts needed for the work: you need to sand the wood along the grain with sandpaper, starting with coarse, and then moving to finer grains, carefully removing dust. Next you need to paint the boards with acrylic or oil paint, apply the desired stencils, symbols or paintings. After this, carefully coat with varnish, repeating this procedure several times and dry.
• An attractive table in a rustic style should be assembled from pallets (also called wooden pallets). In the event that a non-aqueous varnish is used, applying two or three layers is enough, otherwise it is necessary to apply larger number times, approximately up to ten. After completing the varnishing of the elements, it is worth moving on to installation, which consists of several steps.
• We secure the tabletop with planks, firmly connect the boards together and secure them with self-tapping screws. It is mandatory to use a drill to ensure that the wood is not damaged when using self-tapping screws. Then we coat the joints with glue and treat the entire tabletop by special means, protecting the tree from rotting.
• Last of all, we install the legs: we need to screw them with self-tapping screws in order to learn the structure, we install jumpers at the bottom.

1. Wooden table with glued top.

For a glued tabletop, you need to take boards of the same width. For this experiment you will need grooves (and therefore a milling machine). Old floorboards already have grooves; if the appearance of the table is unimportant and its purpose is not for a home, it is worth using them.

• The boards need to be laid out on a completely flat surface; this is important for further assembly of the tabletop.
• Carefully coat the sides with glue, join, avoiding gaps between the boards, then pull the resulting invention together with special tools. Leave the product to dry for one to three days. If the gluing operation of the new tabletop was carried out correctly, then cracks will not appear. If cracks appear, then the tabletop will spread even more.
• The ends need to be processed - first trim them with a jigsaw and then sand them. If draw frame for grinding missing, replace with manual processing– use first coarse, then medium-grit sandpaper. Then carefully varnish the resulting furniture in several layers (about ten layers of varnish, after every third layer you need to treat the surface with sandpaper and remove dust with a damp cloth), in no case rush at this final stage, then installation of the product is required.
• It is required to make massive L-shaped legs. Take boards at least two and a half centimeters thick so that their thickness matches. Connect them at a ninety-degree angle.
• Make a sample on the boards to be joined, coat the joint with wood glue, and then install self-tapping screws. After the glue has dried, coat the parts with varnish and bring them together into the final composition.

Get creative and create your own own home functional, practical and great looking desk! Such a standard piece of furniture can create a certain mood in the premises and enhance your home with special comfort! Choose your material and begin your new adventure - inventing your own table, which may become an ambassador for generations to come! If you still doubt that you can create your own table, you can imagine new furniture in your head, and then give it to professionals for execution, and then, of course, also enjoy the resulting work of art!

Video: How to make a table with your own hands

Photo gallery: DIY wooden tables

IN modern interior common wooden furniture– it adds coziness, such furniture is environmentally friendly and, with proper surface treatment, is easy to clean.

The table itself is an extremely functional invention, in demand in the kitchen, in the workshop, and in the office.

A wooden table combines functionalism, environmental friendliness and aesthetics. You can make such a piece of furniture with your own hands.

If you intend to assemble a table yourself, the first thing you should pay attention to is the material of manufacture. Very rarely, a whole piece of wood is used as a material at hand; much more often, wooden boards are used. Advantages of this material: they can be cut to the required sizes at any construction site; It’s also easy to take them to the assembly site if you have a personal car.

Of the minuses can only be called possible difficulties problems that may arise during installation, and also what you should pay attention to correct processing material - otherwise the boards may come apart and will not last long.

Sexual

This material is used for flooring, for cladding buildings and premises and, according to the topic of this article, for the manufacture of interior items. Advantages such material are as follows:

• Most floorboards have a groove, as this is how they are held together.

  This allows you to fasten the boards into a tabletop without any problems, while the joints will be identical and look aesthetically beautiful;

• Most of the edged boards have already been processed, so after assembling the table you don’t have to resort to additional painting or varnishing the product;
• even if the floorboard is an ordinary edged one, it still fits together with other boards better than the rest.

But the floorboard also has flaws. For example, for a board opened with varnish, a buyer can pay a larger amount than for an ordinary one, with subsequent self-coating. Batten has a limited size, that is, its size will dictate the size of the tabletop, or you will have to adjust the length yourself.

Important. It is impossible to make legs from a floorboard, only a tabletop. This means that you will have to select a different material for the legs.

Unedged

This board has jagged edges with bark, since it is made by longitudinally cutting a tree trunk. Such boards are cheaper, with their help you can achieve original design solutions. But at the same time they demand additional processing, and connecting them is quite difficult.

Oak

They are distinguished by unique strength, density and resistance to many biological and physical influences. Very Expensive, but in terms of service life, this material completely pays for itself.

Drawing

A drawing is necessary, because thanks to it the table will fit exactly into the room. The drawing will also allow you to calculate the volume required material. But first things first. What problems will the drawing allow you to solve?

1. Dimensions. If this kitchen table, and the kitchen is of non-standard sizes, and the table, accordingly, will differ from the standards.
2. Model. Despite the fact that in general idea a table is four legs and a table top, there is huge amount options on how to make it. There are a lot of table models, types of tabletops and legs.
3. Calculation consumables . Having basic mathematical skills, you can calculate the volume of required material from the finished drawing. So that after purchasing the board it does not turn out that there are a lot of scraps left, or that there is not enough material.

Advice. You can download finished drawing from the Internet and modify it to suit your needs.

Tools

To complete the work, you may need the following tools, which should be prepared in advance:

• hammer;
• chisel;
• hacksaw;
• drill;
• plane;
• nail puller;
• saw.

Advice. If further work with the tool is not planned, then you don’t have to buy it, but rent it.

How to do it?

After the material is selected, a drawing is prepared and that’s it necessary tools, you can start for assembly. When drawing up the drawing of the table, all its constituent elements, as well as fastenings, were highlighted. First of all, everything is cut out and turned necessary elements in accordance with and with the dimensions indicated in the drawings. Then, after checking and measuring after production, you can proceed to assembling the parts.

Important. Tools may cause damage. Follow safety precautions.

Assembly order quite simple, you can identify general steps regardless of what model of table you plan to assemble. The assembly steps are as follows:

1. Assembling the legs. The table legs, cut according to the drawing, are fastened with beams using self-tapping screws or nails. For greater reliability, the fastening points should be treated with glue and then tightened with self-tapping screws.

2. Attached to the leg structure table top. To do this, strips are marked on the tabletop that fasten the legs, then using self-tapping screws, nails, screws or fasteners, the tabletop is attached to the structure of the legs.

3. Installation horizontal screed. Many table models require a tie between the table legs to prevent them from moving apart.

Finishing

After the product is assembled, it must be processed. Treatment is necessary so that the product is resistant to the external environment and lasts many times longer than without treatment.

Processing a product means polishing it and then opening with varnish. Most often, sanding and varnishing are done several times for greater reliability.

Photo

We invite you to admire the possible results of the work:

Useful video

All stages of production can be seen in the following video

Conclusion

Table made of wooden planks, made with your own hands, is a wonderful element of the interior that pleases the eye and provides comfort in the home.

A large table is often very necessary for a private home or cottage. It's a great place to sit in the evening with your family or close friends. If you want to put it on the veranda, then it is best to make such a table yourself rather than buy it. The fact is that a product from a store will quickly become unusable due to bad weather.

How to make a kitchen table with your own hands? What types of tables can be made from boards? This and much more will be discussed in this article.

Tools

In order to make such a table, you will need:

• hammer;
• nails;
• shovel;
• oil paint;
• bitumen;
• drying oil;
• jointer;
• plane;
• beam;
• logs without bark.

Material

Initially, you will need to select the type of table, prepare drawings, and only then the material itself. By the way, it can be different:

• Array. Due to its high cost, it is not very popular. The advantage is that it is very easy to make a table from this material.
• Timber and cut boards. Most often, these materials are used in the manufacture of tables.
• Chipboard. Easy to use and highly popular.

Do it yourself

Let us consider in detail the manufacture of a table from timber and boards.

After all the measurements have been taken and the necessary cuts have been made, you will need to sand grinder each element of the future table. Use a damp sponge to collect any dust that appears during the process. After this, you need to cover the wood with a solution - an antiseptic from possible moisture. When the wood is dry, all work can be continued.

It will be necessary to form a support structure from bars and beams. The bars themselves are rounded, and holes of the required diameter are made at the top of the beam. This is necessary for further connection. You will have to make some effort to connect them correctly. It will be better if you pour glue inside.

Now it's time for the tabletop. You will need to cut the board itself in half lengthwise. Between the two sections, lay the rest alternately. If everything is done correctly, you should end up with a loose tabletop.

For the front and back boards, make holes in the center of the other boards on the opposite side. After this, full holes are drilled to a depth that allows the screw to be completely screwed in.

You will need to use screws that are not susceptible to rust. In this case, galvanized screws are perfect. The rail must be screwed onto all joints. Fixation should occur in a checkerboard pattern.

At the final stage, you need to combine the tabletop and legs into one structure. For this you will need metal corners. To make the joints you will need glue. After this operation, the structure is pressed down with a heavy load for six hours. It is best to put plugs of a suitable color on the screw heads.

Final stage

The table is assembled. Now it should be covered with stain and varnish. Once this has been done, the table is left to dry for 36 hours.

To make holes large diameter, you need to use crowns and drill attachments for the drill. With their help, you can form both external and internal contours.

DIY round table (video)

How to make a table from a windowsill

Using the surface under the window, you can easily make a table. The lighting falls perfectly on the windowsill, and with the help of a view of the street you can relax tired eyes.

Materials

To make a table from a window sill, The following materials will be required:

• various screws;
• polyurethane foam;
• sandpaper;
• furniture board from pine;
• chromed metal racks;
• timber to strengthen the window sill;
• glue;
• matte enamel;
• wood putty;
• plastic plugs for racks;
• mounting profiles;
• wood antiseptic;
• polyurethane foam.

Tools

Required tools:

• hacksaw;
• pencil;
• ruler;
• cord;
• roulette;
• paint brush;
• spatula;
• Bulgarian;
• plane;
• electric jigsaw;
• drill.

Manufacturing

First of all, you need to make drawings in such a way that the table from the window sill is convenient for work and does not interfere with the passage. After the measurements have been made, you need to take up the furniture board and its markings. It should be comfortable to sit at the future table. If there is a battery, then your feet should not rest on it.

You will need to cut out the drawn blank from the panel and try it on the window sill. Using a pencil, draw future holes through which hot air from the battery will circulate. If the table is short, you will need one leg in the center.

After this, you need to make short holes across the entire width of the table using a thick drill. To avoid burrs, you will need to treat the surface with sandpaper. Next, the legs are screwed to the tabletop.

The tabletop is secured to the windowsill with liquid nails. The surface is leveled and the legs are adjusted in height. After this, you can consider that the table is ready.

Making a wooden table (video)

Folding table

You also need to consider an option such as a folding table made from a board and a window sill.

First, a piano hinge is attached to the bottom of the window sill. required sizes. The table top is cut out. Several rows of holes are made in it, which will conduct the battery warm air. A crossbar and a pair of legs are made from timber. The product is sanded and varnished. All sawn elements are connected with screws.

The legs with the drawer are attached to the tabletop using a piano hinge. A cover is attached to the window sill. The table perfectly decorates the room and covers the radiator, especially when folded.

How to make a round table with your own hands

From the boards you can make it yourself round table. Previously, in any apartment it was considered necessary attribute. The whole family or friends gathered for it. Moreover, no one sat in the corner, since a round table simply has no corners. Today, these tables are again gaining popularity. Make it happen with my own hands not difficult.

Preparing parts

Parts must be carefully prepared for assembly. The tabletop will be a disk, and the circle will connect the legs and the tabletop itself.

The plywood is sanded and varnished in several layers. The same procedure is repeated with what will be the future legs.

The legs are attached to the tabletop using a plywood ring.

Assembly

Markings are made on the plywood ring for the holes in which the legs will be. In those places that have been marked, holes of the required diameter are drilled.

The legs will be timber, sawn into four parts. They will need to be processed before assembly. The legs are attached to the ring using a screwdriver.

The table must be both beautiful and stable. You need to install two plywood strips crosswise between the table legs under the tabletop.

The entire supporting structure. The plywood ring is connected to the tabletop. After this, the round table is ready.

DIY plank table (video)

Conclusion

You can make it with your own hands from a board various types tables. As you saw from the article, the manufacturing process does not seem complicated. Even a novice home craftsman can handle this.